SEKURE ITI UltraGard Especificaciones descargar pdf

Page 1

Superbus Alphanumeric Touchpad

Superbus Alphanumeric

Touchpad

Document Number: 466-1030 Rev. C

June 1997

Installation

Instructions

Product Summary

The Superbus Alphanumeric Touchpad gives you

complete on-site system programming and operation

control of a compatible system.

The sixteen-character, vacuum-fluorescent

alphanumeric display provides visual status messages

for the entire system. The display identifies any

programmed location so the user can determine where

an alarm, trouble, or open-sensor condition exists.

You can select sensor names from a preprogrammed

list or customize names to suit each customer. Sensor

names are stored in the panel, which eliminates the

need for downloading sensor text from one touchpad

to another.

Touchpad buttons light up after the first press for easy

night viewing. After approximately 15 seconds with

no touchpad activity, this lighting goes out. Pressing

any key will light up the buttons again.

Additional features include the following:

ν Built-in piezo for alarm and status tones.

ν Twenty-four-hour panic buttons for police,

auxiliary, and fire emergencies.

ν One hardwire input (unsupervised).

ν User display brightness control.

Installation Guidelines

ν For UltraGard™ systems, up to eight superbus

devices can be connected to the panel (Superbus

Alphanumeric Touchpad, HIM, ESM, etc.).

ν Each superbus device must have a different unit

number.

ν The touchpad’s default unit number is 1.

ν Maximum current draw of the Superbus

Alphanumeric Touchpad is 75 mA.

ν Do not exceed the panel’s total power when using

panel power for bus devices and hardwire

sensors that require panel power (see the specific

panel’s installation instructions).

ν Mount the touchpad in an environmentally

controlled area (42°F to 95°F).

ν If you use the optional hardwire input, mount the

touchpad near the device connected to the input.

ν When mounting the touchpad’s back plate, allow

a one-inch clearance on all sides, since the

touchpad is bigger than the back plate.

ν Use 4-conductor, 22-gauge or larger stranded wire

from the display to the panel.

ν Use 2-conductor, 22-gauge or larger stranded wire

for the hardwire input.

ν Do not use the hardwire input for a critical

protection device, since this input is not

supervised.

The following must be observed in UL installations:

ν The hardwire input can be configured for

normally closed or normally open protection

devices.

ν If you use the hardwire input and program it

normally closed, mount the touchpad within 3

feet of the panel.

ν If you use the hardwire input and program it

normally open, the panel, touchpad, and

initiating device (hardwire sensor) must be

mounted within 3 feet of each other. No

intervening walls or barriers may be present

between devices.

ν Only UL-listed devices may be connected to the

hardwire input.

ν The hardwire input must not be used for fire-

initiating devices.

60-586

8843G01A.DS4

1 2 3 4 5

Indice de contenidos

Pagina 1 - Touchpad

Page 1Superbus Alphanumeric TouchpadSuperbus AlphanumericTouchpadDocument Number: 466-1030 Rev. CJune 1997InstallationInstructionsProduct SummaryThe S

Pagina 2 - Installation

Superbus Alphanumeric TouchpadPage 2Tools Neededν Screwdriverν #6 screws and anchors ν Panhead screws for a gang box installationν Sheetrock knife or

Pagina 3

Superbus Alphanumeric TouchpadPage 3harness wires:Connect the hardwire sensor to the yellow wireson the wiring harness as shown in Figure 2.Wiring the

Pagina 4 - Troubleshooting

Superbus Alphanumeric TouchpadPage 48. Check the unit number DIP switches on other bus devices (ESM, HIM, HOM, etc.) and make a note of their respecti

Pagina 5 - Specifications

Superbus Alphanumeric TouchpadPage 5ProgrammingThe Superbus Alphanumeric Touchpad must be used to program the panel. For a complete description of pro

Mas documentos para Los Sistemas De Control De Acceso De Seguridad SEKURE ITI UltraGard

a Ver el documento SEKURE ITI UltraGard El manual del propietario

SEKURE ITI UltraGard El manual del propietario (146 paginas)

a Ver el documento SEKURE ITI UltraGard Especificaciones

SEKURE ITI UltraGard Especificaciones (7 paginas)

a Ver el documento SEKURE ITI UltraGard Manual de usuario

SEKURE ITI UltraGard Manual de usuario (28 paginas)

SEKURE ITI UltraGard Manual de usuario (35 paginas)

Comentarios a estos manuales

Sin comentarios

SEKURE ITI UltraGard Especificaciones

Busca en linea o descarga Especificaciones para Los Sistemas De Control De Acceso De Seguridad SEKURE ITI UltraGard. SEKURE ITI UltraGard Specifications [en] Manual de usuario

Indice de contenidos

Mas documentos para Los Sistemas De Control De Acceso De Seguridad SEKURE ITI UltraGard

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE ITI UltraGard