SEKURE Paradox Digiplex DGP-610 Manual de instalación Pagina 20
- Pagina / 54
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
- 19 -
does not apply to bus detectors connected to the
DIGI-BUS.
Example:
The system is armed and the zone speed is set for
600m seconds. A zone opens and closes in less
than 600m seconds, the control panel will not
respond (i.e. no reporting, no alarm and no display
on the keypad).
This prevents any momentary glitches from causing
an alarm or unnecessary reporting. The Input Speed
for each input terminal can be set from 20ms to
5.1s, by programming the desired value (001-255 X
20ms) into the appropriate section.
[201] Control Panel Terminal 1/ Input 001 speed
[202] Control Panel Terminal 2/ Input 002 speed
[203] Control Panel Terminal 3/ Input 003 speed
[204] Control Panel Terminal 4/ Input 004 speed
[205] Control Panel Doubler 1/ Input 005 speed
[206] Control Panel Doubler 2/ Input 006 speed
[207] Control Panel Doubler 3/ Input 007 speed
[208] Control Panel Doubler 4/ Input 008 speed
The optional ZX4 On-Board Zone Expander (see
section 2.13 for details):
[209] ZX4 Terminal 1/Input 009 speed
[210] ZX4 Terminal 2/Input 010 speed
[211] ZX4 Terminal 3/Input 011 speed
[212] ZX4 Terminal 4/Input 012 speed
[213] ZX4 Doubler 1/Input 013 speed
[214] ZX4 Doubler 2/Input 014 speed
[215] ZX4 Doubler 3/Input 015 speed
[216] ZX4 Doubler 4/Input 016 speed
5.6 EOL ZONES
Section [504]: Option [7]
If detection devices connected to hardwired-input
terminals use 1KΩ end of line resistors, enable
option [7] in section [504]. For more information on
the use of EOL resistors, refer to Input Connections
in sections 2.11 & 2.12.
5.7 ZONE DOUBLING (ATZ)
Section [504]: Option [8]
Enabling the ATZ feature allows you to install two
detection devices per zone input terminal. Each
detection device will have its own zone, displaying
zone status on the keypad and sending separate
alarm codes for each zone. The extra zones are
recognized as described in figure 5.5. For
information on how to connect the detection devices,
please refer to Double Zone Connections in section
2.12. Please note that Fire Zones can not be
doubled.
- Digiplex Control Panel 1
- TABLE OF CONTENTS 2
- INTRODUCTION 5
- INSTALLATION 7
- 2.7 BELL/SIREN OUTPUT 9
- 2.8 PROGRAMMABLE OUTPUTS 9
- 2.9 BUS ZONE CONNECTIONS 9
- 2.10 KEYPAD ZONE CONNECTIONS 9
- 2.11 SINGLE ZONE CONNECTIONS 10
- 2.12 DOUBLE ZONE CONNECTIONS 10
- 2.13 CONNECTING THE ZX4 11
- 2.14 KEYSWITCH CONNECTIONS 12
- 2.15 FIRE CIRCUITS 12
- PROGRAMMING METHOD 13
- ACCESS CODES 14
- 4.6 MULTIPLE ACTION FEATURE 15
- 4.5 USER PARTITION ASSIGNMENT 15
- ZONE PROGRAMMING 16
- 5.1 ZONE NUMBERING 17
- 5.2 ZONE DEFINITIONS 17
- 5.3 ZONE PARTITION ASSIGNMENT 18
- 5.4 ZONE OPTIONS 18
- 5.5 INPUT SPEED 19
- 5.6 EOL ZONES 20
- 5.7 ZONE DOUBLING (ATZ) 20
- KEYSWITCH PROGRAMMING 21
- 6.1 KEYSWITCH NUMBERING 22
- 6.2 KEYSWITCH DEFINITIONS 22
- 6.3 KEYSWITCH PARTITION 22
- ASSIGNMENT 22
- 6.4 KEYSWITCH OPTIONS 22
- 7.1 ARMING FOLLOWS PARTITION 24
- 7.2 NO ARMING ON BATTERY FAIL 24
- 7.3 NO ARMING ON TAMPER 24
- 7.4 TIMED AUTO ARMING 24
- 7.5 NO MOVEMENT AUTO ARMING 24
- 7.6 AUTO ARMING OPTIONS 25
- 7.7 ONE-TOUCH FEATURES 25
- 7.8 EXIT DELAY 25
- 7.9 KEYPAD LOCK-OUT FEATURE 25
- 7.10 MAXIMUM BYPASS ENTRIES 26
- 7.12 BELL SQUAWK 26
- 7.13 RING-BACK 26
- 7.14 SWITCH TO STAY ARMING 26
- ALARM OPTIONS 27
- 8.4 KEYPAD PANIC OPTIONS 28
- EVENT REPORTING 29
- 9.1 REPORTING ENABLED 30
- 9.2 REPORT CODES 30
- DIGI-BUS 31
- 9.3 CENTRAL STATION PHONE # 32
- 9.4 PARTITION ACCOUNT # 32
- 9.5 REPORTING FORMATS 33
- 9.6 EVENT CALL DIRECTION 33
- OFF – REPORT ON DISARM 34
- ON – REPORT ON ZONE CLOSURE 34
- OFF – REPORT ON BELL CUT-OFF 34
- 9.12 PAGER DELAY 35
- 9.13 AUTO REPORT CODE 35
- PROGRAMMING 35
- DIALER OPTIONS 36
- PROGRAMMABLE OUTPUTS 37
- 11.3 PGM1 IS SMOKE INPUT 38
- PGM Programming Table 39
- 12.1 HARDWARE RESET 42
- 12.2 SOFTWARE RESET 42
- 12.3 BATTERY CHARGE CURRENT 43
- 12.4 INSTALLER CODE LOCK 43
- 12.5 SYSTEM GUARD LOCK 43
- 12.6 PARTITIONING 43
- 12.7 INSTALLER FUNCTION KEYS 43
- 12.15 POWER SAVE MODE 45
- 12.16 AUTO TROUBLE SHUTDOWN 45
- 12.17 NO AC FAIL DISPLAY 45
- UPLOAD/DOWNLOAD SOFTWARE 46
- 13.6 ANSWER UPLOAD/DOWNLOAD 47
- SOFTWARE 47
- 13.8 CALL BACK FEATURE 47
- USER/KEYPAD FEATURES 48
- FCC WARNINGS 49
- ATTACHMENT LIMITATION NOTICE 50
- - - 50 - 51
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE Paradox Digiplex DGP-610
Los Sistemas De Control De Acceso De Seguridad SEKURE Paradox Esprit 616LED Guía de usuario
(28 paginas)
(28 paginas)
Los Sistemas De Control De Acceso De Seguridad SEKURE Paradox Spectra 1641 Manual de usuario
(47 paginas)
(47 paginas)
Los Sistemas De Control De Acceso De Seguridad SEKURE Paradox Spectra 1686H Guía de usuario
(44 paginas)
(44 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales