SEKURE Paradox Digiplex DGP-610 Guía de instalación descargar pdf (Pagina 33)

EVO Control Panel 29

12 Programmable Outputs

The control panel provides a maximum of 100 mA to PGM1 to PGM4.

PGM5 is a 5A/28Vdc N.O./ N.C. relay output. Activating a PGM changes

it’s state from open to closed or closed to open. Refer to section 2.8 on

page 2.

12.1 PGM Activation Event

The PGM Activation Event determines which event will activate the PGM.

The Event Group specifies the event, the Feature Group identifies the

source, and the Start # and End # sets the range within the Feature Group

(see PGM Programming Table in the "EVO Programming Guide").

Enter the sections that correspond to the Event Group, Feature Group,

Start # and End # of the desired PGM and enter the desired 3-digit number

from the PGM Programming Table:

12.2 PGM Deactivation Option

Once the PGMs are activated, they can deactivate when another event

occurs or after a period of time. Enter the section that corresponds to the

desired PGM and enable or disable option [1] (default = PGM Deactivation

Event):

12.3 Flexible PGM Deactivation Option

The PGM Deactivation Option must be set to PGM Timer for this feature to

function. The Flexible PGM Deactivation Option uses both the PGM

Deactivation Event and the PGM Timer. When enabled, and if the PGM is

activated, it will deactivate when either the PGM Deactivation Event occurs

or the PGM Timer elapses, whichever happens first.

Enter the section corresponding to the PGM and enable option [3]

(default = disabled):

12.4 PGM Deactivation Event

The PGM Deactivation Event determines which event will return the PGM

to its original state. The Event Group specifies the event, the Feature Group

identifies the source, and the Start # and End # determine the range within

the Feature Group.

Enter the sections that correspond to the Event Group, Feature Group,

Start # and End # of the desired PGM and enter the desired 3-digit number

from the PGM Programming Table.

12.5 PGM Timer

When the PGM Deactivation Option is enabled, the PGM Timer determines

how many seconds or minutes the PGM remains activated.

Enter the section that corresponds to the desired PGM and enter a value

from 001 to 255 (default = 005). The value entered is either in seconds or

minutes as determined by the PGM Time Base Selection:

12.5.1 PGM Time Base Selection

The PGM Time Base Selection determines whether the PGM Timers are in

minutes or seconds (default = seconds):

12.6 PGM1 Becomes a 2-wire Smoke Detector Input*

SECTION [3030]: OPTION [1]

(default = disabled) When enabled, PGM1 acts as a zone input for two-

wire smoke detectors. When programming Zone Numbering (see section

4.2 on page 10), the control panel will recognize PGM1 as input number

255. Please refer to section 2.16.1 on page 7 for connection information.

* UL Note: Not verified by UL.

12.7 PGM Test Mode

Entering sections [0901] to [0903] activates the corresponding PGM for 8

seconds to verify if the PGM is functioning as desired.

12.8 PGM Initial Status

Use this option to set the initial state for the PGM.

Event Group Feature Group Start # End #

PGM 1: [0910] [0911] [0912] [0913]

PGM 2: [0920] [0921] [0922] [0923]

PGM 3: [0930] [0931] [0932] [0933]

PGM 4: [0940] [0941] [0942] [0943]

PGM 5: [0950] [0951] [0952] [0953]

PGM 1: [0919] Option Feature

PGM 2: [0929] [1] ON PGM Timer

PGM 3: [0939] [1] OFF PGM Deactivation Event

PGM 4: [0949] [4] ON Normally Closed

PGM 5: [0959] [4] OFF Normally Open

PGM 1: [0919] PGM 2: [0929] PGM 3: [0939]

PGM 4: [0949] PGM 5: [0959]

Event Group Feature Group Start # End #

PGM 1: [0914] [0915] [0916] [0917]

PGM 2: [0924] [0925] [0926] [0927]

PGM 3: [0934] [0935] [0936] [0937]

PGM 4 [0944] [0945] [0946] [0947]

PGM 5 [0954] [0955] [0956] [0957]

PGM 1: [0918] PGM 2: [0928] PGM 3: [0938]

PGM 4: [0948] PGM 5: [0958]

PGM 1: [0919]

Option Feature

PGM 2: [0929]

[2] ON Minutes

PGM 3: [0939]

[2] OFF Seconds

PGM 4: [0949]

PGM 5: [0959]

PGM 1: [0901] PGM 2: [0902] PGM 3: [0903]

PGM 4: [0904] PGM 5: [0905]

PGM 1: [0919] Option Feature

PGM 2: [0929] [4] ON Normally Closed

PGM 3: [0939] [4] OFF Normally Open

PGM 4: [0949]

PGM 5: [0959]

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 63 64

Comentarios a estos manuales

Sin comentarios

SEKURE Paradox Digiplex DGP-610 Guía de instalación Pagina 33

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE Paradox Digiplex DGP-610