SEKURE Paradox Digiplex DGP-610 Guía de instalación descargar pdf (Pagina 34)

30 Reference & Installation Manual

13 System Settings and Commands

13.1 Hardware Reset

A Hardware Reset sets sections [0001] to [3991] to default. Only the Panel

ID, PC Password, PC Telephone Number and Event Buffer are not reset.

The Installer Code Lock prevents Hardware Reset.

1. Make sure the Installer Code Lock is disabled

2. Press and hold the Reset and Aux buttons for 3 seconds

3. The panel will be reset to defaults

13.2 Software Reset

Performing a software reset will set certain parameters to default values or

program certain sections with a set of pre-defined values. To reset:

1. Enter Panel Programming Mode (see section 3.4).

2. Enter section [4049] to unlock software reset.

3. Enter the 4-digit [

SECTION] of the software reset you wish to perform.

4. For every other section your want to reset, you will have to unlock

software reset.

Do not remove power from the control panel.

13.3 Installer Code Lock

SECTION [3001]

(default = 000) Enter 147 into section [3001] to lock all programming. When

147 is programmed, performing a hardware reset as described in section

13.1 will not affect the current panel settings. To remove the Installer Lock,

enter 000 into section [3001].

13.4 Daylight Savings Time

SECTION [3030]: OPTION [3]

(default = enabled) When enabled, the control panel adjusts the system's

clock (time) for daylight saving changes.

13.5 Daylight Savings Time Schedule

SECTION [3022]

(default = 18)

Select the schedule followed for the Daylight Savings Time adjustment.

13.6 Battery Charge Current

SECTION [3030]: OPTION [5]

Depending on the battery’s capacity, enable or disable the option:

A 40VA transformer is required when selecting the 850mA battery charge current, a

20VA transformer may damage the system.

13.7 Combus Speed

SECTION [3030]: OPTION [8]

In large installations, set the speed to High. If you are experiencing

communication troubles, set the speed to Normal or install a Hub (APR3-

HUB2). The control panel will restart when a change is made

Please note that when the combus speed is changed the following

will occur and is considered normal operation:

• The message COMM. TROUBLE CALL SERVICE will be

displayed on keypads connected to the combus.

• The AC and STATUS LEDs will begin to alternately flash and all

operations on the system will be suspended for approximately

one minute while the system reconfigures.

13.8 Transmit Zone Status on Serial Port

SECTION [3035]: OPTION [7]

When enabled, the control panel will transmit zone status information

through the serial port. Use this when there are devices or software

connected to the serial port like WinLoad.

13.9 Serial Port Baud Rate

SECTION [3035]: OPTION [8]

Adjust depending on the baud rate set in WinLoad or NEware:

If communication between the control panel and the computer is

experiencing difficulty at 57,600 baud, especially over long

distances reduce the baud rate of the software to 38,400 baud.

[4040]

Resets the programmable sections from [0001] to [3991] to

default (even if Installer Code Lock is enabled) except: Event

Buffer, Panel ID, PC Password, PC Telephone Number and Zone,

Door, Partition and User Labels (see section 14.4 on page 34).

[4041] Resets the System Master Code to 123456.

[4042]

Resets all Zone Programming sections from [0001] to [0196],

[0201] to [0296] and [0961] to [0984] to default.

[4043]

Resets the Access Control sections, except Door Labels (see

section 13.25 on page 32), from [2201] to [2712] to default.

[4044]

Resets all User Access Code Programming sections from [1001]

to [1999] and [2001] to [2199] to default. User Labels (see

section 14.4 on page 34) will not be reset.

[4045]

Resets all control panel settings from [3020] to [3043] and from

[3900] to [3991] and all the Dialer sections from [3051] to [3081].

[4046]

Resets all Partition Settings, except Partition Labels (see section

13.25 on page 32), from [3101] to [3831] to default.

[4047]

Resets Keyswitch Programming sections from [0501] to [0832]

and all Programmable Outputs sections from [0901] to [0939] to

default.

[4048]

Entering this section resets the User Labels from the User

Access Codes, the Zone Labels from [0301] to [0396], Door

Labels from [2301] to [2332], Partition Labels [3100], [3200],

[3300], [3400], [3500], [3600], [3700] and [3800] to default.

[4049]

Entering this section will unlock software reset for sections [4040]

to [4048].

Canada/United States/Mexico/

St-Johns/Bahamas/Turks and

Caicos

01 Cuba

02 Brazil 03 Chile

04 Falkland Islands 05 Paraguay

European Union/United

Kingdom/Greenland

Russia and surrounding

countries

South Australia/Victoria/

Australian Capital Territory/

New South Wales

09 Tasmania/Lord Howe Island

10 New-Zealand/Chatham 11 Tonga

12 Iraq/Syria 13 Israel (TBC)

14 Lebanon/Kirgizstan 15 Palestine

16 Egypt 17 Namibia

Canada/United States 2007

(default)

19 New Zealand

[5] ON 850mA

[5] OFF 350mA (default)

[8] ON High Speed

[8] OFF Normal Speed (default)

[8] ON 57,600 baud

[8] OFF 38,400 baud (default)

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 63 64

Comentarios a estos manuales

Sin comentarios

SEKURE Paradox Digiplex DGP-610 Guía de instalación Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE Paradox Digiplex DGP-610