SEKURE Paradox Digiplex DGP-610 Guía de instalación descargar pdf (Pagina 50)

46 Reference & Installation Manual

3.3.12 Keypad Tamper Enable

SECTION [006]: OPTION [5]

3.3.13 Combus Voltmeter

1. From Normal Mode press and hold the [0] key.

2. Enter the [

INSTALLER CODE] (Default: 000000).

3. Press [

ACC].

The voltage may drop during the control panel battery test.

3.4 Programmable Output Options

3.4.1 PGM State

SECTION [006]: OPTION [1]

The PGM can provide 50mA to any device connected to it.

3.4.2 PGM Deactivation Mode

SECTION [006]: OPTION [2]

3.4.3 PGM Base Time

SECTION [006]: OPTION [3]

3.4.4 PGM Override

SECTION [006]: OPTION [4]

When the PGM override is enabled, the keypad's on-board PGM will ignore

PGM Activation Events (section 3.4.6), PGM Deactivation Events (section

3.4.7), and PGM Timers (section 3.4.5). It will remain in its normal state

until the PGM Override is disabled. This option may be used to test the

PGM connections.

3.4.5 PGM Timer

SECTION [008]

The value programmed in section [008] represents how long the PGM will

remain in its opposite state after being activated. To program the timer,

enter a 3-digit decimal value (000 to 255) in section [008]. Default: 5

seconds.

3.4.6 PGM Activation Event

SECTIONS [009] TO [012]

Enter the sections that correspond to the Event Group, Feature Group,

Start # and End # of the PGM and enter the required data.

3.4.7 PGM Deactivation Event

SECTIONS [013] TO [016]

If the PGM Deactivation Option is set to follow the PGM Deactivation event,

the PGM will return to its normal state when the event programmed in

sections [013] to [016] occurs.

Enter the sections that correspond to the Event Group, Feature Group,

Start # and End # of the PGM and enter the required data.

3.5 EVO641R Programming

3.5.1 Partition Assignment

SECTION [001]: OPTIONS [1] TO [8]

To assign the keypad to a partition, enable the option that corresponds to

the desired partition. By default, partitions 1 to 8 are enabled.

3.5.2 Display Access Code Entry

SECTION [003]: OPTION [1]

Option [1] OFF=Digits are replaced by a “*“(default)

Option [1] ON=Access Code digits will be displayed

3.5.3 Display Exit Delay Timer

SECTION [003]: OPTION [2]

Option [2] OFF=Will not display Exit Delay timer (default)

Option [2] ON=LCD screen will display Exit Delay timer

3.5.4 Display Entry Delay Timer

SECTION [003]: OPTION [3]

Option [3] OFF=Will not display the Entry Delay Timer (default)

Option [3] ON=LCD screen will display Entry Delay Timer

3.5.5 Confidential Mode

SECTION [003]: OPTIONS [4] AND [5]

Section [003]:

Option [4] OFF=Normal Mode (default)

Option [4] ON=Confidential Mode

Option [5] OFF=LCD screen activated by entering an access code (default)

Option [5] ON=LCD screen activated by pressing a button

3.5.6 Confidential Mode Timer

SECTION [007]

Section [007] determines the amount of time without action before the

keypad enters Confidential Mode. The Confidential Mode Timer can be set

from 005 seconds to 255 seconds. Default: 120 secs.

3.5.7 Time Display Option

SECTION [003]: OPTION [8]

Option [8] OFF=Date displayed as yy/mm/dd (default)

Option [8] ON=Date displayed as dd/mm/yy

3.5.8 Muting

SECTION [004]: OPTION [1]

Option [1] OFF=Audible sounds (default)

Option [1] ON=Mute

3.5.9 Beep on Exit Delay

SECTION [004]: OPTION [2]

Option [2] OFF=Exit Delay beep disabled

Option [2] ON=Exit Delay beep enabled (default)

3.5.10 Chime on Zone Closure

SECTION [004]: OPTION [4]

Option [4] OFF=Chime on Zone Closure disabled (default)

Option [4] ON=Chime on Zone Closure enabled

Option [3] ON = Beep enabled: Module and Bus Troubles

Option [4] OFF = Beep disabled: all Zone Troubles (default)

Option [4] ON = Beep enabled: all Zone Troubles

Option [5] OFF = Keypad's tamper is disabled (default)

Option [5] ON = Keypad's tamper is enabled

Option [1] OFF= PGM is Normally Open (default)

Option [1] ON= PGM is Normally Closed

Option [2] OFF = Deactivates on PGM Deactivation Event (default)

Option [2] ON = PGM will deactivate according to the PGM Timer

Option [3] OFF = PGM Base Time is 1 second (default)

Option [3] ON = PGM Base Time is 1 minute

Option [4] OFF = PGM Override disabled (default)

Option [4] ON = PGM Override enabled

Event Group Feature Group Start # End #

PGM

[009] [010] [011] [012]

Event Group Feature Group Start # End #

PGM

[013] [014] [015] [016]

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 63 64

Comentarios a estos manuales

Sin comentarios

SEKURE Paradox Digiplex DGP-610 Guía de instalación Pagina 50

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE Paradox Digiplex DGP-610