SEKURE Paradox Spectra 1686H Manual de instalación Pagina 34
- Pagina / 60
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
32 REFERENCE & INSTALLATION MANUAL
be delayed (see Pow er Failure Report D elay on page 36).
• BATTER Y FA IL URE: backup battery is disconnected or battery voltage is ≤10.5V.
• AUX IL IAR Y SUPPLY: Auxiliary power supply has overloaded (current consumption is >1.1A).
Section [206]
• BEL L OUTPU T OVE R LO AD : Bell/si ren output has overloaded (see page 7).
• BEL L OUTPU T DISC ONNECT ED: Devices connected to the Bell Output have been disconnected.
• TIMER LOSS: The control panel has detected a loss in time or clock failure (see page 40)
• FIRE LOOP TR OUBL E: The control panel has detected a tam per trouble on a fire zone.
Section [207]
• WIRELESS LOW BA TTER Y: The battery voltage of a Liberator or Omnia wireless transmitter (motion
detector or contact switch) has dropped below recommended limits.
• MODUL E FAU LT: Will report if all keypads connected to the control panel have been disconnected or if a
module with its corresponding supervision option enabled in the control panel (see pages 41 and 42) is
disconnected.
• PRINTER FAULT: An error has occurred on the Printer Bus Module.
• FAIL TO COMM UNICA TE: The control panel has fail ed all attempts to communicate with the central
station. The report code will be transmitted upon the next successful attempt.
8.2.11 SYSTEM TROUB LE RESTORE REPORT CODES
Sections [208] to [210]
Whenever the system restores one of the troubles listed in section 8.2.10, the control panel can send the
appropriate report code to the central station identifying the type of system trouble restore. If Telephone
Line Monitor ing is enabled ( see page 36) , the control panel can also transmi t a T LM Restore report code.
8.2.12 SPECIAL REP O RT IN G CODES
Sections [211] to [213]
Whenever the system generates one of the instances listed below, the control panel can send the
appropriate report code to the central station identifying the type of system occurrence.
Section [211]
• COL D START: The control panel was completely shutdown (no battery, no AC) and then was re-started.
• TEST REP O RT : A test report has been generated automatically (see page 36).
• N ot available
• PC EXIT: The control panel has ended communication with WinLoad.
Section [212]
• INSTALLER IN : Installer has entered the pr ogrammi ng mode.
• INSTALLER OUT: Installer has exited the programming mode.
• Future use
• Future use
Section [213]
• TX SUPERVISION LOS S : Wireless Transmitter Supervision (see SPC- 319 Instruction Sheet) has been
enabled and a transmitter is no longer communicating with the system.
• TX SUPERVISION RESTORE: Reports when the above trouble has been restored
• Future use
• Future use
8.3 CENTRAL STATION TELEPHONE NUMBERS
Section [1 51 ] = Ph one#1 , [1 52] = Phon e#2, [15 3] = Backup Phon e#: Up to 32 digits
The Spectra Control Panels can dial up to 2 different central station telephone numbers. You can enter any digit
from 0 to 9 and any special keys or functions (see Table 7) up to a maximum of 32 digits. For more information on
how these telephone numbers are used, please refer to Event Call Direction on page 34 and Re porting Form ats in
section 8.5. After the Maximum Dialing Attempts (see page 35) to one central station telephone number have failed,
the control panel will then dial the backup telephone number. If the Alter na te D ial Option (see page 35) is enabled,
the control panel will dial the programm ed backup telephone number after every failed attempt. If no backup
telephone number is programmed, the control panel will never report to the backup telephone number. Also refer to
Delay Between Dialing Attempts on page 35.
- SPECTRA CONTROL PANELS V2.1 1
- TABLE OF CONTENTS 3
- LIST OF TABLES 4
- PART 1: INTRODUCTION 5
- PART 2: INSTALLATION 6
- 2.2 EARTH GROUND 7
- 2.3 AC POWER 8
- 2.4 BACKUP BATTERY 8
- 2.6 TELEPHONE LINE CONNECTION 8
- 2.7 BELL OUTPUT CONNECTION 9
- 2.9 SINGLE ZONE INPUTS 10
- 2.12 KEYSWITCH CONNECTIONS 11
- PART 3: PROGRAMMING METHODS 12
- SPECTRA SERIES 11 13
- PART 4: ACCESS CODES 15
- 4.1 ACCESS CODE LENGTH 16
- 4.4 USER CODE OPTIONS 16
- 4.6 DURESS CODE 17
- 4.5 LOCK MASTER CODE 17
- PART 5: ZONE PROGRAMMING 18
- 5.4 ZONE PROGRAMMING 19
- 5.5 ZONE DEFINITIONS 20
- 5.7 ZONE PARTITION ASSIGNMENT 22
- 5.8 ZONE OPTIONS 22
- 5.9 ZONE SPEED 24
- 5.10 EOL ZONES 24
- 6.1 SWITCH TO STAY AR MING 25
- 6.2 STAY ARMING WITH DELAY 25
- 6.6.1 AUT O-ARM TIMER 26
- 6.8 AUTO-ARMING OPTIONS 27
- 6.9 ONE-TOUCH ARMING 27
- 6.10 EXIT DELAY 27
- PART 7: ALARM OPTIONS 28
- 7.3 TAMPER RECOGNITION 29
- 7.4 KEYPAD PANIC OPTIONS 29
- 7.5 PANIC LOCKOUT TIMER 30
- SPECTRA SERIES 29 31
- 8.2 REPORT CODES 32
- Sections [208] to [210] 34
- Sections [211] to [213] 34
- 8.4 PARTITION ACCOUNT NUMBERS 35
- 8.5 REPORTING FORMATS 35
- 8.6 PAGER DELAY 36
- 8.7 EVENT CALL DIRECTION 36
- SPECTRA SERIES 35 37
- PART 9: PROGRAMMABLE OUTPUTS 39
- PART 10: SYSTEM SETTINGS 41
- 10.6 SYSTEM REAL-TIME CLOCK 42
- 10.7 CLOCK ADJUST 42
- SPECTRA SERIES 43 45
- 11.1 PANEL ANSWER OPTIONS 46
- 11.2 PANEL IDENTIFIER 46
- 11.3 PC PASSWORD 46
- 11.4 PC TELEPHONE NUMBER 46
- 11.5 CALL WINLOAD SOFTWARE 47
- 11.6 ANSWER WINLOAD SOFTWARE 47
- 11.8 CALL BACK WINLOAD 47
- PAR T 12: USER OPERATION 48
- 12.2 PROGRAMMING ACCESS CODES 49
- 12.4 REGULAR ARMING 50
- 12.5 STAY ARMING 50
- 12.6 INSTANT ARMING 50
- 12.7 FORCE ARMING 51
- 12.9 ONE-TOUCH ARMING 51
- 10-ZONE LED KEYPAD: 52
- 12.15 KEYPAD MUTING 53
- FCC WARNINGS 54
- SPECTRA SERIES 53 55
- SPECTRA SERIES 55 57
- IN CANADA 02/2003 17X8-EI07 60
© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales