SEKURE DGP2-648 Manual de instalación descargar pdf (Pagina 38)

36 REFERENCE & INSTALLATION MANUAL

12 ACCESS CODES

12.1 INSTALLER CODE

SECTION [1000]

(Default: 000000) The Installer Code is used to enter the control panel's

programming mode, which allows you to program all the features, options

and commands of the control panel and any modules on the combus. The

Installer Code is six digits in length where each digit can be any value from

0 to 9. To change the Installer Code:

1) Press and hold [0]

2) Enter [

INSTALLER CODE]

3) Key in [1000]

4) Enter new 6-digit [

INSTALLER CODE]

The Installer Code can program the User Code Options and the

Partition Assignment, but cannot program the personal

identification numbers.

12.2 ACCESS CODE LENGTH

ECTION [3033]: OPTIONS [2] AND [3]

Access codes can be 1 to 6 digits in length. When programming access

codes with less than 6 digits, press the [

ENTER] key after entering the last

digit. The control panel automatically removes the last 2 digits of the User

Access Code if the length is changed from 6 digits to 4 digits. However, if

the User Access Code Length is changed from 4 digits to 6 digits, the

control panel adds 2 digits to the end by using the first 2 digits.

For example, if the User Access Code is 1234 and you switch to 6 digits,

the code will become 123412.

12.3 SYSTEM MASTER CODE

ECTION [1001]

(Default: 123456) The Installer Code can change the User Code Options,

Partition Assignment and Access Control Options, but cannot change the

personal identification number (PIN). Each digit in the System Master Code

can be any value from 0 to 9. To reset the System Master Code, refer to

section 11.2 on page 32. With the System Master Code, a user can use any

of the available arming methods with access to all partitions and can

program all User Access Codes, User Options, Partition Assignments and

Access Control Options.

12.4 PROGRAMMING ACCESS CODES

ECTIONS [1002] TO [1999]

(Default = all options are off) The control panel supports 998 User Access

Codes. In sections [1002] to [1999], the Installer Code can program the

User Code Options, Partition Assignment and Access Control Options, but

cannot program the personal identification numbers (PIN). To program the

PINs, refer the users to the System Manager’s Manual. The System Master

Code or a user with the Master feature enabled can program the User Code

Options, Partition Assignment, Access Control Options and User Labels

using a different method of programming.

If no partition assignment is selected, the User Access Code will

only be able to activate PGMs.

To program user labels, refer to the LCD Keypad System

Manager’s Manual or to the Grafica Graphic LCD Keypad Online

Help.

Figure 12-1: Programming User Access Codes

12.5 USER OPTIONS

ECTIONS [1002] TO [1999]: USER OPTIONS SCREEN, OPTIONS [1] TO [8]

The User Options define how each User Access Code can arm or disarm

the partitions. All users can Regular Arm (see section 15.1) their assigned

partitions, but only those with the Arm Only option disabled can disarm an

assigned partition.

Enable or disable the options as required for each User Access Code as

shown in Figure 12-1.

Option Description

[2] [3]

OFF OFF

4-digit User Access Code (Default)

OFF ON

6-digit User Access Code

ON ON

Flexible User Access Code

Press & hold

the [0] key

Where sections [1002] to [1999] represent

User Access Codes 002 to 999.

Key in the

[

INSTALLER

CODE]

Enter

[

SECTION]

User Options

Feature Select

Programming

Press the [S] key

User

Partition

Assignment

Feature Select

Programming

Press the [S] key

Access

Level &

Schedule

Assignment

Enter digits

Access

Control User

Options

Feature Select

Programming

Press the [S] key

Enter

Access Card

Press [ENTER]

or [S] to save

and go to the

next section.

User Options

[1] [2] Feature

off off Master Feature Disabled

on off User can program PIN

on on User can program User Options,

Partition Assignment, PIN, and all

Access Control options

[3] Duress [6] Stay & Instant

[4] Bypass [7] Force

[5] Arm Only [8] off = Access keypad’s partitions

on=Access user’s partitions

* Note: all users can regular arm.

Partition Assignment

[1] User Code has Access to Partition 1

[2] User Code has Access to Partition 2

[3] User Code has Access to Partition 3

[4] User Code has Access to Partition 4

[5] User Code has Access to Partition 5

[6] User Code has Access to Partition 6

[7] User Code has Access to Partition 7

[8] User Code has Access to Partition 8

Access Level & Schedule Assignment

First Brackets: Access Level

Enter Level from 00 to 15 (00 = all doors)

Second Brackets: Schedule

Enter number from 00 to 15 (00 = all times)

Access Control Options

[1] Access Control

[2] Can Disarm with Access Card

[3] Card with Door Unlocked Period Extension

[4] [5] Feature

off off Cannot Arm with Card (arming disabled)

on off Can Regular Arm with Card

off on Can Stay Arm with Card

on on Can Force Arm with Card

[6] Add Tolerance Window to Schedules

[7] off = Code can arm, disarm & access anytime

on = Code follows Schedule

[8] off = Valid Card can be granted access and

disarm partition

on = Valid Card can be granted access, but

Code required to disarm partition

Access Card Assignment

Enter Access Card's serial number manually or

present Card to the reader.

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 63 64

Comentarios a estos manuales

Sin comentarios

SEKURE DGP2-648 Manual de instalación Pagina 38

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE DGP2-648