SEKURE DGP2-648 Manual de instalación descargar pdf (Pagina 41)

DIGIPLEXNE CONTROL PANEL 39

Start Time and End Time during the holidays. An Interval cannot cross into

another day (overnight). Schedules are assigned to the users through their

User Access Codes (refer to the System Manager’s Manual).

For example, program Schedule 001 in section [2401]:

A = Start time 09:00, End time 17:00, options 2, 3, 4, 5, and 6 enabled

B = Start time 10:00, End time 17:00, options 1, 7, and 8 enabled

Then, any User Access Code with this Schedule assigned will have access

Monday to Friday from 9AM to 5PM and on Saturday, Sunday and Holidays

from 10AM to 5PM.

Primary Schedules 001 to 015 are programmed in sections [2401] to

[2415] respectively. Secondary Schedules 016 to 032 are programmed in

sections [2416] to [2432] respectively. For each Schedule enter the Start

Time, End Time and enable or disable the options as required for each

Interval. Schedule 000 allows the user access at all times. Only Primary

Schedules can be assigned to User Access Codes. Secondary Schedules

are used as Backup Schedules (see section 13.7).

13.7 BACKUP SCHEDULES

SECTION [2501] TO [2532]

When an Access Card or User Access Code is used at an Access Door, the

control panel verifies whether it was used during its assigned Primary

Schedule. If the Primary Schedule is linked to another Schedule, it will

verify the linked Schedule and any Schedule linked to it. The control panel

will verify up to 8 linked Schedules, one after another, until it determines

whether the card or code is valid. Each Schedule (Primary or Secondary)

from 001 to 032 can be linked to another Schedule in sections [2501] to

[2532] respectively. In each section enter the 3-digit Schedule number of

the Schedule to be linked with it.

For example, if Schedule 001 is linked to Schedule 005 and Schedule 005

is linked to Schedule 030, then the control panel will verify Schedules 001,

005 and 030.

13.8 HOLIDAY PROGRAMMING

ECTIONS [2701] TO [2712]

Holiday Programming identifies the days that are considered holidays in the

Schedules. When option [8] is enabled in sections [2401] to [2432], access

is permitted during the holidays. Each section from [2701] to [2712]

represents a month from January to December respectively. Each section

includes four groups of five to eight options that represent the days of the

month. Enable the options representing the holidays.

For example, if [1] and [2] are enabled in the first screen in section [2701],

then January 1 and 2 are designated as holidays.

13.9 SCHEDULE TOLERANCE WINDOW

ECTION [3039]

The Schedule Tolerance Window lengthens the assigned Schedule of

some users. User Access Codes with Add Tolerance Windows to

Schedules enabled have the number of minutes programmed in [3039]

added before and after their Schedule. This feature can be used instead of

creating Schedules for each shift and each shift’s supervisor by assigning

the supervisors to their respective shift’s Schedule and enabling Add

Tolerance Windows to Schedules on their User Access Codes. Enter any

value between 001 and 255 (default = 000) to determine Schedule

Tolerance Window in minutes.

For example, if 060 is programmed in section [3039], users with Add

Tolerance Windows to Schedules enabled will have their Schedule

extended by 1 hour before and 1 hour after their assigned Schedule (see

Figure 13-2).

Figure 13-2: Example of a Schedule Tolerance Window

The Schedule Tolerance Window applies to Access Schedules

only (section 13.6). The Schedule Tolerance Window does not

apply to the Arming and Disarming Report Schedules (section

8.3.1 and section 8.3.2).

13.10 DOOR ACCESS MODE

ECTION [2251] TO [2282]: OPTION [1]

Each Access Door can be assigned to one or more partitions in the security

system and each user can be assigned to one or more partitions. This

means that the actions performed by the user will be directly linked to the

partition(s) assigned to that door. Doors 01 to 32 are programmed in

sections [2251] to [2282] respectively. For each door enable or disable the

option as required:

13.11 CODE ACCESS

ECTION [2251] TO [2282]: OPTION [2]

Code Access can allow access to an Access Door by entering a valid User

Access Code and pressing the [

ACC] key on a DGP2-641 LCD Keypad

instead of using the Access Card. The control panel will verify the User

Access Code’s validity in the same way it would verify the Access Card (i.e.

through its assigned Access Level and Schedule). Doors 01 to 32 are

programmed in sections [2251] to [2282] respectively. For each door

enable or disable the option as required:

This option is not available for LED and Grafica Keypads.

13.12 CARD AND CODE ACCESS

ECTION [2251] TO [2282]: OPTION [3]

For higher security areas, the Access Door can be programmed to require a

user to present a valid Access Card and then enter the same user’s valid

code before access is granted. The Access Card must be presented to, and

the user code must be entered on, a PosiPIN™ Proximity Card Reader and

Keypad (CR-R885-BL) that is connected to an Access Control Module

(DGP2-ACM1P). PosiPIN and the Access Control Module must be

configured to allow access of this type. Please refer to the PosiPIN

Installation and Operating Instructions, and to the Access Control Module

Reference & Installation Manual for programming instructions. Doors 01 to

32 are programmed in sections [2251] to [2282] respectively. For each

door enable or disable the option as required:

Section Start Time

1st Screen

End Time

2nd Screen

Days

3rd Screen

Schedule 001: [2401]

Schedule 032: [2432]

set as per

24hr. clock

set as per

24hr. clock

[1] = Sunday (S)

[2] = Monday (M)

[3] = Tuesday (T)

[4] = Wednesday (W)

[5] = Thursday (T)

[6] = Friday (F)

[7] = Saturday (S)

[8] = Holidays (H)

set as per

24hr. clock

set as per

24hr. clock

Option Feature

[1]

“OR” Access Door

The Access Door grants access or permits arming or

disarming to users assigned to at least one of the door’s

partitions. An “OR” door will arm or disarm only the

partitions that it has in common with the users.

[1]

OFF

“AND” Access Door

The Access Door grants access or permits arming only to

users assigned to all the door’s assigned partitions.

Option Feature

[2]

[ACC] key enabled

[2]

OFF

Access with Card only

User’s assigned Schedule is 9AM to 5PM. When Add Tolerance Windows to

Schedules is enabled for the user, the user has access from 8AM to 6PM.

Schedule Tolerance Windows

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 63 64

Comentarios a estos manuales

Sin comentarios

SEKURE DGP2-648 Manual de instalación Pagina 41

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE DGP2-648