SEKURE DGP2-648 Manual de instalación descargar pdf (Pagina 44)

42 REFERENCE & INSTALLATION MANUAL

15 USER FEATURES

15.1 REGULAR ARMING

This method is used for the everyday arming of the system. All zones within

the partition must be closed to arm the system. The system can also be

Regular Armed by using a One-touch Feature (see section 6.15) or a

Keyswitch (see section 5.4.3). All users are able to Regular Arm the

partition(s) assigned to their User Access Codes. Refer to How to Arm on

page 42 for information on how to Regular Arm the system.

15.2 STAY ARMING

Stay Arming partially arms the partition to permit the user to remain in the

partition. Stay Zones (see section 4.5.3) will not arm when Stay Arming.

Partitions can also be armed by the Stay Arm One-touch Feature (see

section 6.15) or a Keyswitch (see section 5.4.4). Only User Access Codes

with the Stay and Instant Arm option enabled can Stay Arm a partition.

For example, arm the doors and windows without arming the motion

detectors. Refer to How to Arm on page 42 for information on how to Stay

Arm the system.

15.2.1 Stay Arming with Delay

Stay Arming with Delay functions like Stay Arming except armed zones are

programmed with an Entry Delay Timer (see section 4.3.14). If a zone is

triggered, the delay starts allowing the user time to disarm the partition(s).

15.3 INSTANT ARMING

Similar to Stay Arming, Instant Arming partially arms the partition to permit

the user to remain in the partition, but all Delay zones become Instant

zones. Partitions can also be armed by the Instant One-touch Feature (see

section 6.15) or a Keyswitch (see section 5.4.6). Only User Access Codes

with the Stay and Instant Arm option enabled can Instant Arm a partition.

Refer to How to Arm on page 42 for information on how to Instant Arm the

system.

15.3.1 Instant Arming with Delay

Instant Arming with Delay functions like Instant Arming except armed zones

are programmed with an Entry Delay Timer (see section 4.3.14). If a zone

is triggered, the delay starts allowing the user time to disarm the partitions.

15.4 FORCE ARMING

Force Arming allows the user to arm a partition when Force zones are open

(see section 4.5.4). Once the open zone in an armed partition is closed, the

system will then arm it as well. This feature is commonly used when a

motion detector is protecting an area that is occupied by a keypad. The

system can also be Force Armed by using a One-touch Feature (see

section 6.15) or a Keyswitch (see section 5.4.5). Only User Access Codes

with the Force Arm option enabled can Force Arm a partition.

For example, during Force arming the motion detector remains unarmed

until the user exits the area. The system will then arm the motion detector.

Refer to How to Arm on page 42 for information on how to Force Arm the

system.

15.5 HOW TO ARM

The following section details how to arm the system using an LCD or

Grafica keypad.

For LCD Keypads: To arm, users:

1) Enter their [

ACCESS CODE].

2) Press the key corresponding to the desired arming method (see

Table 13 on page 42). If the users have access to more than one

partition, they can press the key(s) corresponding to the desired

partition(s) or press [0] to arm all their assigned partitions.

For Grafica Keypads: To arm, users...

1) Enter their [

ACCESS CODE].

2) Using the scroll keys, highlight the desired arming method (see

Table 13 on page 42) and then press the center action key (Ok). If the

users have access to more than one partition, proceed to step 3.

3) Highlight either Arm All Areas or Select Area(s) and then press the

center action key (Ok). If the user(s) selected the Select Area(s)

method, follow steps 4 and 5.

4) Highlight a partition you wish to arm and then press the left action key

(Select). Repeat this step for any additional partition.

5) Press the center action key (Arm).

15.6 DISARMING

All users can disarm, except users with Arm Only (see section 12.5)

enabled on their User Access Codes. Users can only disarm the partitions

assigned to their User Access Codes. The Stay or Instant Armed partitions

can also be Disarmed by using a One-touch Feature. To disarm, users...

For LCD Keypads:

1) Enter through a designated entry. The Entry Delay Timer will begin.

2) Enter their [

ACCESS CODE].

3) Press the [

DISARM] key. If the users have access to more than one

partition, they can press the key corresponding to the desired partition

or press [0] to disarm all their assigned partitions.

For Grafica Keypads:

1) Enter through a designated entry. The Entry Delay Timer will begin.

2) Enter their [

ACCESS CODE].

3) Using the scroll keys, highlight Disarm and then press the center

action key (Ok). If you have access to more than one area, proceed to

step 4.

4) Highlight either Disarm All Areas or Select Area(s) and then press

the center action key (Ok). If you selected the Select Area(s) method,

follow steps 5 and 6.

5) Highlight the area you wish to disarm and then press the left action

key (Select). Repeat this step for any additional area.

6) Press the center action key (Disarm).

15.7 BYPASS PROGRAMMING

Bypass Programming allows users to program the security system to ignore

specified zones the next time the partition is armed. To bypass a zone, the

zone must have the Bypass option enabled, the User Access Code must

have the Bypass option enabled, and the zone must be within the User

Access Code’s partition assignment. To Bypass, users...

For LCD Keypads:

1) Enter their [

ACCESS CODE].

2) Press the [

BYP] key.

3) Enter the zone’s 2-digit number or use the [

S] and [T] keys and

press the [

BYP] key when the zone appears on-screen.

4) Press [

ENTER] key to exit.

For Grafica Keypads:

1) Enter their [

ACCESS CODE].

Table 13: Arming Methods

Arming Method LCD Grafica

Regular [ARM]

(Arm System)

Stay [STAY]

(Stay Arm)

Instant [5]

(Instant Arm)

Force [FORCE]

(Force Arm)

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 63 64

Comentarios a estos manuales

Sin comentarios

SEKURE DGP2-648 Manual de instalación Pagina 44

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE DGP2-648