SEKURE DGP2-648 Manual de instalación descargar pdf (Pagina 46)

44 REFERENCE & INSTALLATION MANUAL

Step 3: If more than one Trouble Group appears, highlight the desired

group before pressing the center action key (View) to view the

specific trouble.

If Access Control is enabled in the system and the option Door

Access during Clock Loss is

ON (section [3038] option [8]), only the

System Master Code and User Codes with the Master feature

enabled will be able to program the clock. Enter the System Master

or a Master Code, press [

TRBL], then continue with the steps above.

15.13 TROUBLE LATCH

ECTION [3033]: OPTION [6]

With the Trouble Latch feature disabled, when a trouble occurs and is

corrected, the trouble is automatically cleared and no longer displayed.

With the Trouble Latch feature enabled, the trouble will remain displayed

until it is manually cleared by the user. To clear the trouble, the user must

enter the trouble display (see section 15.12) and then exit the trouble

display. For LCD and LED keypads, press [

CLEAR] to exit. For Grafica

keypads, press the left action key (Back) to exit.

Only troubles that have been corrected can be cleared. If a

trouble has not been corrected, it will continue to be displayed

even if the user tries to clear the trouble by using the method

described above.

15.14 CLEAR BELL CURRENT LIMIT TROUBLE

ECTION [3030]: OPTION [7]

(Default: OFF) When an activated bell output is shorted, a Bell Current Limit

trouble is displayed and can be sent to the Central Station. This feature

determines how the Bell Current Limit trouble is cleared.

UL Note: For UL installations, section [3030] option [7] must be

enabled (ON).

Only troubles that have been corrected can be cleared. If a

trouble has not been corrected, it will continue to be displayed

even if the user tries to clear the trouble through the trouble

display.

Trouble Description

GROUP [1]: SYSTEM

[1] AC Failure

Power failure detected. The system is

running on the backup battery.

[2] Battery Trouble

The backup battery is disconnected, needs

to be recharged or replaced.

[3] AUX Current Limit

Devices connected to AUX have exceeded

current limits (1.1A). The Auxiliary Output

will shutdown until the trouble is corrected.

[4] Bell Current Limit

The bell or siren has exceeded current

limits (3A). The Bell/Siren Output will

shutdown until the trouble is corrected.

[5] Bell Absent

The bell or siren is not connected. When

the bell output is not used, connect a 1kΩ

resistor across the bell output.

[6] ROM Check Error

The control panel registers a data memory

error. Contact distributor for replacement.

[7] RAM Check Error

The control panel registers a work memory

error. Contact distributor for replacement.

GROUP [2]: COMMUNICATOR

[1] TLM1

The control panel is unable to access the

main telephone line.

[2] Fail to Communicate 1

[3] Fail to Communicate 2

[4] Fail to Communicate 3

[5] Fail to Communicate 4

The control panel tried all assigned

telephone numbers and failed to contact

the Monitoring Company.

[6] Fail to Communicate PC

The control panel is unable to

communicate with the WinLoad software.

GROUP [3]: MODULES

[1] Module Tamper A module’s tamper switch was triggered

[2] ROM Check Error

A module is experiencing a data memory

error. Contact distributor for replacement.

[3] TLM Trouble

A module is unable to access the

telephone line.

[4] Fail to Communicate

A module failed to communicate with the

Monitoring Company.

[5] Printer Trouble

The control panel registers a problem with

a printer connected to a Printer Module.

Check printer for problems (paper jam, no

paper, no power, etc.).

[6] AC Failure Module power failure.

[7] Battery Failure Module's battery is disconnected, needs to

be recharged or needs to be replaced.

[8] Supply Output Module has exceeded current limits.

GROUP [4]: NETWORK (COMBUS)

[1] Missing Keypad

A keypad is no longer communicating with

the control panel.

[2] Missing Module

A device is no longer communicating with

the control panel.

[3] General Failure

No communication between the devices

and the control panel.

[4] Combus Overload

Too many devices (over 127) are on the

combus.

GROUP [5]: ZONE TAMPER

Press [5] to display zone(s) Zones displayed were tampered.

GROUP [6]: ZONE LOW BATTERY

Press [6] to display zone(s)

Zone displayed indicates where a wireless

device’s battery needs to be replaced.

Also, the device’s yellow light will flash.

GROUP [7]: ZONE FAULT

Press [7] to display zone(s)

A smoke detector is experiencing a wiring

problem, needs to be cleaned, or a

wireless device is no longer communicating

with its receiver (supervision loss).

GROUP [8]: CLOCK LOSS

Press [8] to re-program

The time and date were reset to default.

Step 1: Press the [8] key

Step 2: Set the hour and minutes according

to the 24-hour clock (i.e. 9AM is

09:00 and 9PM is 21:00).

Step 3: Enter the correct date according to

yyyy/mm/dd.

Step 4: Press [

CLEAR] to exit.

Option Description

[7]

When an activated bell output is shorted, the Bell Current

Limit trouble will remain displayed until it is manually

cleared by the user. The user must clear the trouble

through the trouble display.

[7]

OFF

When an activated bell output is shorted, the DigiplexNE

control panel will attempt to reactivate the bell output once

every minute for as long as the bell is activated. The Bell

Current Limit trouble is cleared automatically the first time

the control panel does not detect a short when attempting

to reactivate the bell.

Trouble Description

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 63 64

Comentarios a estos manuales

Sin comentarios

SEKURE DGP2-648 Manual de instalación Pagina 46

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE DGP2-648