SEKURE Paradox Digiplex DGP-610 Manual de instalación descargar pdf (Pagina 41)

Digiplex DGP-NE96 - 41 - Programming Guide

Download Memory Key to Control Panel.

1) Insert the Memory Key (PMC-3) onto the control panel’s connector labelled “MEM KEY”.

2) To download the contents of the Memory Key except sections [0001] to [0096] and [0501] to [0532], enter installer programming

mode and then enter section [4010].

To download the contents of the Memory Key including sections [0001] to [0096] and [0501] to [0532], enter installer programming

mode and then enter section [4011].

3) When the keypad emits a confirmation beep, remove the Memory Key.

Copy Control Panel to Memory Key

1) Insert Memory Key (PMC-3) onto the control panel’s connector labelled “MEM KEY”. Ensure the write protect jumper on the memory

key is on.

2) To copy the contents to the Memory Key except sections [0001] to [0096] and [0501] to [0532], enter installer programming mode,

then enter section [4020].

To copy the contents to the Memory Key including sections [0001] to [0096] and [0501] to [0532], enter section [4021].

3) After the confirmation beep, remove the Memory Key. Remove the Memory Key’s jumper if you do not wish to accidentally overwrite

its contents.

Automatic Report Code Programming

When using Contact ID or SIA Reporting formats (section [3070] on page 32), default report codes can be programmed automatically. After automatic

defaults are set, they can be changed and the remaining report codes can be set manually.

Software Reset

Performing a software reset will set certain parameters to default values. To do so:

1) Make sure the “

RESET” jumper (see page 49) on the control panel is ON.

2) Enter Programming Mode (see page 1).

3) Enter the 4-digit [

SECTION] corresponding to the software reset you wish to perform:

Section Description

[4030]

ALL REPORT CODES RESET TO 00

Resets all the report codes from sections [0201] to [0296], [0701] to [0832],

[2001] to [2199] and [3900] to [3999] to 00.

Sections [4031] to [4037] reset all the report codes in the following sections to

the default values from the “Automatic Report Codes List” on page 42:

[4031]

ALL REPORT CODES RESET TO FF [0201] to [0296], [0701] to [0832], [2001] to [2199] & [3900] to [3999]

[4032]

ZONE ALARM/ALARM RESTORE AND ZONE TAMPER/TAMPER

ESTORE REPORT CODES

[0201] to [0296]

[4033]

USER/KEYSWITCH ARMING & DISARMING REPORT CODES [0701] to [0832], and [2001] to [2199]

[4034]

SPECIAL CODES [3900] to [3909]

[4035] S

PECIAL ARMING/DISARMING REPORT CODES [3910] to [3929]

[4036] S

PECIAL ALARM REPORT CODES [3930] to [3939]

[4037] T

ROUBLE & TROUBLE RESTORE REPORT CODES [3940] to [3999]

Section Description

[4040] Entering this section will reset all programmable sections from [0001] to [3999] to factory default values.

[4041] Entering this section will reset the system master code to 123456.

[4042]

Entering this section will reset all Zone (sections [0001] to [0196], [0201] to [0296], and sections [0961] to [0984]) programming to default

values.

[4043] Entering this section will reset all access control sections from [2201] to [2712], excluding door labels, to default values.

[4044] Entering this section will reset all user code sections from [1001] to [1999] and [2001] to [2199] to default values.

[4045] Entering this section will reset all dialer (sections [3051] to [3081]) and control panel (sections [3020] to [3043], and [3900] to [3991])

programming to default values.

[4046] Entering this section will reset all partition sections from [3101] to [3829], excluding partition labels, to default values.

[4047] Entering this section will reset all PGM (sections from [0901] to [0939]) and all Keyswitch (sections [0501] to [0632]) programming, as well

as all Keyswitch arming/disarming report codes (sections from [0701] to [0832]) to default values.

[4048] Entering this section will clear all user labels, door labels, partition labels, and zone labels from sections [0301] to [0396].

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 51 52

Comentarios a estos manuales

Sin comentarios

SEKURE Paradox Digiplex DGP-610 Manual de instalación Pagina 41

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SEKURE Paradox Digiplex DGP-610